How to add an amplifier to your car audio system. Step 2 specify 2 or 4 ohm single voice coil or 2 or 4 ohm dual voice coil subwoofers the subwoofer wiring diagram tool will then display two wiring options with the final impedance at the amplifier.
Use the speaker wires that you disconnected from the rear speakers and connect them to the subwoofer on the terminals.
Wiring diagram how to install car amplifier and subwoofer. You will just need to run the larger gauge speaker wire from your amplifier to your subwoofer. 1 How To Install Car Subwoofer. Disconnect the wires on the rear speakers.
Sub car amplifier wiring diagram installation. This simplified diagram shows how a full-blown car audio system upgrade gets wired in a car. Oct 5 2015 – Car Audio Amplifier Instalation GuideAmplifier and speakers wiring.
Connect the remote to the stereo and the signal source. The ground should go from the ground terminal of the amplifier to the ground of a car. Our wiring diagrams will help you find the best way to wire your subs and amps so youll get the best performance out of your gear.
All you need to do is to connect power and ground wires to the amplifier. The following wiring diagram shows the additional wiring youll need to add a subwoofer to a factory system. Speaker-level signals are not very prone to picking up interference so its okay to run your speaker wires near power cables.
Connect your 2 channel HIlo converter to a left and right output signal behind your radio. If you do not want to be stuck with a substandard stereo system its time to do something about itYou need a decent subwoofer to add a bit more grunt to your music. Of course you will also need some speakers and most importantly a powerful amplifier to feed all these new.
In most cases this wire is red. How to add an amplifier to your car audio system. Youll need these items for the installation and to give it that.
Start by getting a subwoofer amplifier or powered sub with speaker-level inputs. Run the patch cables along a path other than the amplifier power cable. 13 Connect the amplifier to the subwoofer.
Connect the amplifier ground wire to bare metal near where the amplifier and subwoofer will be placed. The amplifier does not always come with wire connection. Connecting the positive wire to the fuse holder Connect the ground wire the metal near the area where you intend to place the amplifier and woofer.
The power wire should go from the car battery to the positive terminal on your amplifier. The power cable will cause audible interference if grouped with signal cables. The system includes a 4-channel amp for the front and rear pairs of full-range speakers and a mono amp for a subwoofer.
The best way to do that is to run a new speaker wire from each amplifier output to each speaker. The extra gear youll need for wiring the amps includes. 12 Place the subwoofer in the box.
11 Wiring the subwoofer. Use a wiring harness adapter. Nice sharing for how to install a subwoofer amplifier and enclosure.
Use a crimp ring terminal and secure it to the car. Httpsamznto2VsaY3TWiring kit similar to the one I used. Use 14- or 16-gauge wire for speakers 12- or 14-gauge for subwoofers.
This simplified diagram shows how a full-blown car audio system upgrade gets wired in a car. 14 Setting up the subwoofer. This is usually a lot easier.
2 Installing Amplifier and Subwoofer from Start to Finish In 10 Minutes. Like any music loving car owner you are probably feeling a bit disappointed with your current factory audio setup. Connect the negative wire that comes from the subwoofer box with the right speaker wire and the positive to the left speaker wire.
The system includes a 4-channel amp for the front and rear pairs of full-range speakers and a mono amp for a subwoofer. Connect the equalizer patch cables to the stereo and run them to the trunk. Amplifier installation wiring kit.
Attatch your RCA wires to that RCA channel and run that to. Put the subwoofer box in the car trunk. The other steps include.
You need a kit amp wiring harness sold separately.